Poultry Feed Chemicals-97

Chlorine Liquid appears as a greenish-yellow  Chlorine has high electron affinity & high electronegativity.

Directions for Use and Dose Rates

Soak Method:-
It may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime.Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand.In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise,RXSOL-22-2201. can be used undiluted especially when deposition is heavy and hard spots persist.

Cleaning Procedure

Conventional cleaning methods such as a brush,hard sponge, thick and hard broom and /or a mop can be used on heavy duty and hard stain deposits.Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of RXSOL-22-2201 is sufficient to cover a surface area of 8–10 square meters.

NOTE ::: -- Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.

Note:-
• Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
• Stubborn deposits should be scrubbed to assist the cleaning operation.

Your local Rx CLEANSERS representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.

Dirt attached on air-side fins of air coolers are a mix of carbonaceous particles such as soot and oil mist of unburned fuel components. 
Carbonaceous particles can be removed by Alkaline Cleaners Part No. RXSOL-16-1040-025 ( www.rxmarine.com/alkaline-air-cooler-cleaner ) and oil mist can be removed by oil based cleaners. However, it is very difficult to remove the mix of these substances. If you use an alkaline cleaner, oil will repel the water based alkaline cleaner; if you use oil based cleaner, carbonaceous particles will get in the way and stop oil from being removed.

This cleaners designed to remove both carbonaceous and oil simultaneously. An effective cleaning method is to immerse one side to remove the loose stains first, and then immerse the other side. This method can efficiently remove dirt and prevent swollen dirt peeled from fins from blocking the spaces between fins.

Dirt in tubes of seawater side

White scales attached on the seawater side of air coolers of many vessels. We found that in most cases, the main component of the scales is calcium carbonate and there is also a small amount of calcium sulfate. Therefore in most cases, if you dissolve the calcium carbonate the scales will be removed.

However, if the amount of scales is large enough to block the tube, the cylindrical scale will usually have calcium carbonate on the outside (the side that is in contact with tube) and calcium sulfate in the center (part that seawater passes through). Calcium sulfate is easier to be formed when the temperature goes higher.

When the amount of scales increases, the contact area of scale and cleaner is very small and a longer time of dissolution is required. Calcium sulfate cannot be dissolved by an acid cleaner.

Typical dosage range is between 1 and 6 mg/L. Maximum dilution is temperature related as shown:

Important Note: Over and under-dosing may cause membrane fouling so please contact RX Marine International representative to define the optimal feed point and dosage rate. Maximum Dilutions

Normal soil:
Dilute 10 to 20ml A217 per litre of warm water (1:100 to 1:50).
Heavy soil and restoration: Dilute 50ml per litre of warm water (1:20).
Ceiling cleaning: Add 50ml "Safe Bleach OxiBrite" ( www.rxmarine.com/colour-safe-bleach ) Part No. - RXSOL-41-8731-025,  per 5 litres of Renovate Industrial solution. (Observe cautions below).

Pressure washing: 
Mix 1 part Renovate Industrial Multi Purpose Cleaner with 4 parts water and meter at desired setting.Always pre-test surface in an inconspicuous area before proceeding. Do not use on water sensitive fabrics, unsealed wood, aluminium or other delicate surfaces.Apply by sprayer, sponge or floor machine. Allow 2 to 5 minutes contact time for heavy soil, scrub if needed, then rinse surface thoroughly with clean water.  Observe all safety precautions. ear suitable personal protective equipment and cover all sensitive furnishings.