Tank Cleaner-20

• Use cold - No Heating required.
• Easily dissolves deposits containing carbon , polymer resin etc.
• Economical to use.
• Scraping not required.
• Non- flammable.
• Helpful for burner tips, fuel injectors and all components fouled by carbon, resin or varnishes.
• Cleans oil side of fuel heaters, oil coolers, etc.
• Can be used for cleaning of : -Fuel Oil Filters - Pistons - Piston rings - Valve cage

It is used to clean weld seams and surrounding areas with brush. It is used to remove heavy scales, discolouration, annealing colours, rust particles near weld and welding affected area by heat.

Circulation method : For closed system like PIPE , use concentrated materials atleast for 1-2 Hrs . Then FLUSH the system with TECHNICAL GRADE OF DI-WATER ( which is free from , all SOLUBLE IMPURITIES )

Spray Method : For TANK PASSIVATION , this is very effective method . Directly spray on wall of TANKS atleast for 10-15 Minutes , then wash the system with cupious amout of fresh water , finally use TECH GRADE DI water for complete wash.

Procedure of Passivation

1. Isolate the exchanger and set up a circuit with an external tank with heating coil inside and a pump to circulate cleaning solution.

FLUSHING:-

2. Flush the Exchanger with fresh water to remove loose material (like dirt etc.) till such time clear water comes.

INHIBITED ACID CLEANING:-

3. Circulate inhibited Acid (5-6 % Citric Acid and 1% Rodine 213) along with non ionic wetting agent like RXSOL-T300  through Exchanger Loop for 6 to 8 hours
4. It total iron concentration reaches 5000 - 8000 PPM and concentration below 2% acid percentage then dump the cleaning solution and repeat the cycle with fresh inhibited acid.
5. Samples to be tested for pH, TDS and iron on hourly basis.
6. Normal operating temperature should be 50-60º C.
7. When iron concentration and acid concentration of solution reaches steady state and cleaning in completed. Drain the cleaning solution.

NEUTRALIZING:-

8. Circulate 1-2% solution of soda Ash for one to two for neutralization.
9. Rinse the neutralizing solution with water till pH of Inlet and Outlet is same.

PASSIVATION:-

10. Immediately fill and Circulate with 1-3% of solution of sodium Hexametaphosphate for 4-6 hours keeping operating temperature around 50-60º C. Analyze for Phosphate levels in Inlet and Outlet. (Normally maintain 30-40 PPM O-PO4 level)
11. Drain the passive solution without flushing with water.

DRYING:-

12. Dry the circuit with dry air/N2.

This product is recommended as a wall and floor cleaner in industrial facilities. May be used in pressure washer applications or hand steaming. Powerful cleaner/degreaser with controlled foam. Variable dilutions for the wide variety of applications. Economical choice. Effective cleaner. 

This is an aqueous surfactant solution, alkaline base, food-grade phosphate product. Effective for degreasing and removal of oil residue, animal fat and vegetable bases on different surfaces: industrial equipment, including food, assemblies, transport, tanks, walls, floors and other surfaces, manual and machine washing of textiles and clothing. It has an average foaming capability when applied by hand or with the help of floor cleaning machines, pressure washers, equipment for foam cleaning. 

• Food service establishments

• Hotels and motels

• Educational facilities

• Any general cleaning task

• Heavy Industries and in PLANT area

This product is recommended as a wall and floor cleaner in industrial facilities,  food service establishments hotels and motels educational facilities any general cleaning task.

It is also used in mechanical engineering, petroleum, and food industries, railway transport, office and warehousing, utilities and other industries.

During the operation, the fins & tubes of the main engine air cooler which become fouled with oil, grease, dust and carbonaceous deposit, which will affect cooler efficiency and damage the system.

RXSOL-54-1048-020 ( www.rxmarine.com/safe-acid-descalex-liquid-20-ltr ) is a powerful dissolving agent of calcium carbonate. Therefore, it is better to use RXSOL-54-1048-020  to do circulating cleaning at an early stage before the scales build up and block the tube, or regular cleaning is recommended as well. It is impossible to do a circulating cleaning when the tube is completely blocked.

Hold Cleaning Chemicals ALKAA Tuff High Foam Foam concentrate can be delivered in ports worldwide. Specially our stron network in India and Middle East makes us no1 supplier of hold cleaning chemicals. It is a heavy duty non corrosive concentrated cleaning compound soluble in fresh and salt water , also suitable with high pressure cleanig machines. Ideal for difficult cleaning problems faced in industrial and other plants,  Very effective degreaser which removes dirt, oil and grease from the equipment, parts, components, engines, floors and walls etc. 

ALKAA Tuff HIGH FOAM LIQUID - HD (RXSOL-22-3033-025)

The Importance of ALKAA Tuff High Foam concentrate by High-Pressure Cleaning

The job of high pressure cleaning can be done easier & quicker by simply using ALKAA Tuff High Foam concentrate correct dosages. Using a high pressure cleaner alone, without any CLEANER, will not  achieve  optimal cleaning results High-pressure cleaning primarily refers to cleaning of Hard  surfaces, such  as Decks, Tanks, Engine-rooms, etc. and in the majority of cases the cleaning is done according to the so-called two-step method:

3 Pieces of Good Advice:
Apply  ALKAA Tuff High Foam concentrate on dry surface where possible! A dry surface will absorb far better than a wet surface. When applying ALKAA Tuff High Foam Foam concentrate on vertical surfaces: Start application from the bottom and work upwards! If beginning from the top and going downwards, the ALKAATUFF High Foam concentrate may produce "channels" down the surface, thereby running too fast off the surface. During high pressure cleaning: It is important that the rinsing water does not run over non-cleaned surfaces! The rinsing water can draw soap from the surface if running over non-cleaned surfaces. High pressure together with optimum concentration of ALKAATUFF High Foam concentrate will give the best effect .

Product Description:-ALKAA Tuff High Foam concentrate is a superior & powerful alkaline cleaner containing corrosion inhibitors to prevents the corrosion of   metals . It is low toxic product with an exceptional solvency power on soil & oily  matter & having good foaming qualities. It is free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling materials .

Applications:- ALKAA Tuff High Foam concentrate Suitable for cleaning engine components like fuel and  Lube oil filters, Injection nozzles, pump components, inlet  and  exhaust valves &  primarily refers to cleaning of  hard surfaces, such as Decks, Tanks, Engine-rooms,  etc. can be used for all  types of cleaning and degreasing and  may be applied by brush, handspray, high and low pressure washing machines etc.

Directions for Use and Dose Rates:
General Cleaning:- ALKAA Tuff High Foam concentrate can be used for all types of cleaning &  degreasing & may  be applied by  Brush, Hand spray, high and low pressure washing machines etc. Time necessary for cleaning depends on the nature and  thickness of the deposits. 20-30 min. will suffice for   most applications. Hardened, carbonised or aged deposits may require up to 4 hours. If  the cleaning  solution is not heavily contaminated, it may be re-used at a later stage. If allowed to cool, the de-gassing procedure must be repeated. Depending on degree of contamination RxTuff should be mixed with warm water at a rate of 50-200 ml   per 10 litres. i.e. 1 cup of RxTuff to a bucket of water. RxTuff solution can  be applied  simply by mops, brushes or rags, or by dipping the soiled articles into  the ALKAATUFF High Foam concentrate solution. After cleaning, rinse off with cold or warm water. Due to high foaming properties, ALKAA Tuff High Foam concentrate is not recommended for washing machines.                        

Tank Cleaning:-Cargo tank cleaning to remove residues of Mineral, Animal, Vegetable or Fish oil, Waxes  &  Soot from inert gas systems.

Method of Application and Dose Rates:-

• Direct injection method for tank washing machines. Dose rate 1-5 litres per ton wash water (0.1-0.5%).
• Recirculation method. Dose rate 1-7 litres per ton wash water (0.1-0.7%).
• Spot cleaning. Hand spray neat or diluted with up to 5 parts water and leave for several minutes before rinsing off with clean water.

Cleaning of Cargo Tanks to Remove Soot from Inert Gas Systems:-

• Spray ALKAA Tuff High Foam concentrate  on with a high pressure cleaning machine and  use 1:6 with water. If used with hand sprayer, spray  the product  neat onto the surface, allowing 1 lit. for every 12 m2. Use a 5-8% solution in a tank washing machine.
• Leave for about 30-45 minutes. The surface should be kept wet.
• Wash down with hot water (80°C) and check the cargo tank.
• Repeat the procedure if necessary.