Leather Chem-96

Directions for use
Note: Exercise caution when removing radiator caps. Release pressure slowly to avoid scalding.
 

• Turn on the heater and add required amount of RX 400 to a warm radiator.
• Run the engine for 20 minutes minimum (no longer than 1 hour). Stop the engine and allow it to cool.
• Drain the system by removing the bottom radiator hose or opening the drain cock. Thoroughly flush and rinse out all old coolant. Replace the hose or close the drain cock.
• Add RXSOL 4001  corrosion inhibitor and clean, soft or demineralised water, or
• Where specified, use anti-freeze/anti-boil coolant (such as RXSOL-4004 ultra Coolant).
• Start the engine, check for leaks and top up as necessary.
   

Dose Rates

• All cars and light commercials - add 500 ml
• For trucks, tractors and large engines - add 500 ml for every 6 litres (quarts) of cooling system capacity.

DIRECTIONS FOR USE :

• Rub on dirty surface,  (do not use water) until dirt and grease are dissolved.
• Wipe with dry cloth or rinse with water.

After using  RXSOL-40-1048-025, sense all metal surfaces with 0.5 percent of  RXSOL-10-1005, at least 2-4 hour , up to neutral of PH value.

• Fast and effective scale remover.
• Soft on ferrous metals.
• Removes water scale & rust from boilers/diesel engine & other cooling system
• As well as from condensers, evaporators, & heat exchangers etc
 

Why Use RXSOL Descaler?

• It is a safe , economical concentrated  chemical to be used on the waterside of heat transfer equipment.
• You do not have to heat RXSOL-40-1048-025 .
  RXSOL-40-1048-025  is safer for the employees to use than other acid products.

• Your equipment will be cleaned in only hours without disassembling any part of the equipment. Equipment can also be cleaned without any down time (cleaning on the run).

•  Cleans down to the original surface without pitting.
•  RXSOL-40-1048-025 is safe on copper, copper-nickel, bronze, brass, iron, stainless steel and rubber.
•  RXSOL-40-1048-025  will extend the usable life of your equipment, especially when used as a part of a regularly scheduled preventative maintenance program.
•  Removing the scale build up allows your equipment to operate more efficiently with less down time.

TIPS for General Uses ::: 

The steam boiler which has solid mass of mineral deposits approximate mass calculation will help to use proper volume of RXSOL-40-1048-025  Descaler. As per gallon in concentrated form of RXSOL-40-1048-025  has the ability to dissolve approximately 1.5kg of scale mass 
For example if descaling required for home appliances , brewing shop 1 - 3 Table spoon is sufficient to clean while for Industrial cleaning multiple Gallon volume required.

As for the other parts,  The RXSOL-40-1048-025 works more quickly with hot water than cold. Try using RXSOL-40-1048-025 with the hot maintain the temperature. And give sufficint time to dissolve mineral deposits in some cases complete dissolving may reuqire bath water above 100F over night period.

Home application ::: 
Around two tablespoons to a liter of water is a 'normal' mix. You could go 3 or 4 tablespoons for heavier scale. When I do my every 6 months descale I use the 2 tablespoons per liter mix and it works just fine. Hot water is more aggressive so when you put all the parts in a tub to descale, put your water and RXSOL-40-1048-025 in a bit stock pot, bring it to a low boil then dump it in your tub with the parts.

Almost forgot, do not use an aluminum pot or Teflon coated. Use stainless. The acidic part of RXSOL-40-1048-025 will eat up the aluminum and may blister the Teflon. 

The recommended dosage for Brine Corrosion Inhibitor RX is 17.5 litres per tonne of brine in the system. Brine Corrosion Inhibitor Rx may be added directly to the system either neat or in a water dilution. Dilutions should be made with evaporated water. If a chemical dosing pump is used then pump and lines should be mild steel, stainless steel, Teflon, polyethylene, PVC, polypropylene or rubber.

Conversion from chromate Brine corrosion inhibitor RX is compatible with chromate. Systems with chromate need not be flushed before adding the product. Let chromate deplete naturally and maintain boron level at a minimum of 70ppm. Brine Corrosion Inhibitor Rx should be fed slowly. Start feeding 5 to 10% of the total dosage at a time and watch for foaming. Gradually increase the feed rate. Brine Corrosion Inhibitor Rx does not induce foaming at normal dose rates, but if it is fed too much too soon, foaming may occur. Feed lines and pumps should be mild steel, stainless steel, Teflon, polyethylene, PVC polypropylene or rubber.

Testing and Control Control Brine Corrosion Inhibitor RX as Boron at 70 - 100 ppm Note: Because the specific gravity of the brine varies with concentration, the resulting level of boron should be calculated.

Maintain Temperature of floor in between 10 degrees C and below 37 degrees C. Also for out side application it will not rain for several hours. CLEAN surface completely mainly make OIL grease, wax free, If possible before one days or Air movers can be used to shorten drying time. . Check the absorbency of each slab before proceeding. Spray section with water to determine how absorbent the concrete is and if absorbency is consistent. This will also help you determine the coverage that should be expected. 

Apply RXSOL  Densifier undiluted with lowpressure sprayer. Apply enough product to wet the surface without forming puddles. Spread evenly with soft synthetic brush. After application surface should take minimum 5 to 10 minutes to dry if dryness occurs immediately or in 2 - 3 minutes then apply densifier again. Allow treated surfaces to dry before any additional procedures are initiated. After drying, remove any powdered residue using a stiff brush before continuing. At this point the floor can be polished and/or sealed. Polishing time will be reduced and the surface will absorb less sealer.. Adjust procedures and/ or applications appropriately.