Textiles / Looms-91

House Hold : One of the most common uses of hydrogen peroxide is as a disinfectant. Spray it on surfaces like kitchen counter top and wipe with a clean rag. It can be used as a mouthwash too. You have to dilute the chemical with water and use it for rinsing the mouth. This mouthwash is also said to whiten teeth. Ensure that you do not swallow the liquid, while rinsing.
It can also be used to wash vegetables and fruits, in order to get rid of germs and pesticides. Add some hydrogen peroxide to a bowl full of water (you may also add a few pinches of salt). Soak the veggies and fruits for some time. Remove them and rinse with cold water, before use.This chemical is also used to purify water in swimming pools.
 

Agriculture : Farmers use it as an insecticide. They spray diluted form of this chemical, on plants, so that the pests and weeds get killed, without causing harm to the plants. Its also used for watering plants. Mix an ounce of this chemical with a quart of water and use it on plants. Apart from boosting the level of oxygen in the soil, this mixture is also said to prevent root rot. Some people soak seeds in it, after diluting it with water. It is said that this will fasten the process of germination. For this purpose have to mix 1.5 teaspoons of hydrogen peroxide in a cup of water.

Textile: It acts as a stain remover. Put 1 spoon tea in 1 bucket water  and let it sit for a while. After that, rinse the stains with water and soap.
As it has bleaching property, it is used as a bleach too.

IIndustrial :

Reduced Sulfur Compound Treatment for Refinery Wastewater

Sulfur compounds, such as hydrogen sulfide, thiosulfates and mercaptans, can present serious refinery wastewater problems. Hydrogen peroxide treatment is a cost effective way to treat these reduced sulfur species.

Supplemental Dissolved Oxygen to Reduce BOD and COD

Hydrogen peroxide has been used to reduce BOD and COD in refinery wastewater Supply of Supplemental Dissolved Oxygen (DO) when biological treatment systems experience temporary overloads or equipment failure.Predigestion of wastewater which contains moderate to high levels of compounds that are toxic, inhibitory or recalcitrant to biological treatment.As indicated by these examples, hydrogen peroxide can be used as a stand-alone treatment or as an enhancement to existing physical or biological treatment processes, depending on the situation.

Wastewater Pretreatment
Hydrogen peroxide is one of the most versatile, dependable and environmentally compatible oxidizing agents. The relative safety and simplicity of its use as an oxidizing agent has led to the development of a number of applications in refinery wastewater systems.

After uses of solvent type cleaner to make Hydrocarbon free tank, RINSE the tank Throughly—preferably with running continuous water. For critical Tank cleaning, Make a fresh 1% solution of Advance Tank cleaner in cold, warm, or hot water. If available use warm water. For difficult soils, raise water temperature and use more detergent.

Otherwise for Spot Cleaning: Spray  Advance Tank cleaner directly or it can be diluted up to 5 parts, And leave up to 30 minutes to complete the reaction then finally flush off with water. Always remember  do not allow to dryon surface, then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages.  Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.

Re-circulation Method:–

Fill tank with fresh water and heat up to warm 30-40oC .  Then start adding Advance Tank cleaner 0.03 to 9% ( for general wash use 300 ML for 1000 Ltr water and ratio can be increase upto 9 Ltrs for 1000 Ltr water )  to circulate the water.   A stronger solution can be made for critical cleaning. Finally lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material. Use a strainer at the pump stack when circulating any solution. Finally rinse the tank with hot water.

LIME Marine should be used as directed and at any temperature within the operating limits between 0°F / -18°C and 180°F / 82°C. If the solution does freeze, slush or thicken at the lower operating temperatures, and then thaws, there will be no performance reducing results. Please consult the manufacturer when temperatures above 180°F are encountered.
RXLYME Marine should be applied at ambient temperatures with no heating required. The solution is exothermic, but does not develop a substantial increase in temperature while dissolving water scale, rust, mussels, barnacles, zebra mussels, tiger shells and other water formed deposits.