Search

Metal Treatment-68

Nitric Acid

Packing Size: 
25.00 Kg
Short Description: 
Passivation chemical
  • 63 reads

Cool Water Treat

Alias: 

C.W.T. Inhibitor 9-111, COOL WATER TREAT NCL, Coolwater Treat, Cool water treat, Cool Treat, Corrosion Inhibitor for Cooling Water, CoolTreat 25 Ltr

Active Matter: 
45-50
Application: 

Cool Water Treat  is a highly effective corrosion inhibitor for all common metals in cooling water systems. Testing has shown no detrimental effects on non metallic substances such as seals, glands, packing, hoses, gaskets etc., normally used in these systems. Where most traditional inhibitors react with the metal surface and form oxides that prevent further corrosion, Cool Water Treat  applies a thin and durable layer of protective molecules to the metal surfaces. This technology prevents the continuous build-up of insulating layers on heat transfer surfaces. For new builds, RXSOL  Ships Service recommends cleaning of the water system before commencing service. The system will always contain small amounts of oil and iron oxides, and this can be removed in one operation. If the system is corroded or is more heavily contaminated, degreasing scale is recommended. For systems previously treated with other products, RXSOL  Ships Service recommend to drain and flush the system before refilling with distilled water and Cool Water Treat . The system should be clean and free from scale and corrosion products when starting the treatment. The use of antifreeze is sometimes required if the vessel is to be laid up in cold areas, Cool water treat can be used in conjunction with glycols for frost protection. If used in conjunction with glycols, It is recommended to increase the product concentration to 8%.*

Packing Size: 
25.00 Ltr.
Using Procedure: 

Cool Water Treat should be dosed to a suitable point in the system. If the expansion tank is used, adequate circulation must be assured.

Dosing and Control

Initial dosage for an untreated system is 60 litres of Cool Water Treat Cool water Treat Corrosion Inhibitor / ton of untreated distilled water (6%). This will provide sufficient protection of the system for a period of two to five years under normal conditions. 6% Cool water Treat Corrosion Inhibitor should also be dosed in all make up water added to the system to compensate for lost coolant. The engine manufacturer's recommendations for water quality should always be complied with. Chloride levels should always be as low as possible. Most engine manufacturers recommend a maximum of 50 ppm chlorides. For this reason, RXSOL Service recommends the use of distilled water as make-up.

Note: 
  • Liquid product, easy to use
  • Environmentally friendly, fully organic product, low toxicity
  • Effective against cavitation and erosion. Superior heat transfer properties
  • Compatible with hoses, gaskets and seals
  • Compatible with glycols for frost protection
  • Stable product-non depleting
  • The product can be used for corrosion inhibition in many types of closed re-circulation system cooling water systems
  • Approved by major engine manufacturers
Related Products: 
ROCCOR NB Corrosion Scale Inhibitor Liquid
Air Cooler Scale Dissolver
Engine Guard NB Scale Inhibitor DEWT
Safety Accessories: 
Coolant Extended Life RXSOL ELC
Metal Bright
ENGINE SCALE Guard NB
Short Description: 
Cool water Treat Corrosion Inhibitor can be used in conjunction with glycols for frost protection. If used in conjunction with glycols, It is recommended to increase the product concentration to 8%.*

Cool Water Treat is specialized corrosion inhibitor for Cooling Water system.

#CorroSionInhibitor_CoolingSystem
#CoolingWaterTreatmentChemicals
#CWTinhbitor_ManufacturerSupplierIndiaUAEoman

Cool Water Treat corrosion inhibitor for cooling water system manufacturer and supplier in Mumbai, Navi Mumbai, Gandhidham, Hazira Surat, Chennai Ennore, Vizag Visakhapatnam, Kolkata Haldia, Buzbuz, Paradip, Fujairah, Dubai, Ajman, Abudhabi, Muscat, Oman, Canada, Nairobi Kenya, Sudan, Yemen

Cooling Water Corrosion Inhibitor

Sodium Hypo Chlorite

Sodium Hypochlorite solution, Used for sterlizing water and swimming pool...This will - Remove odors. Remove Color. Improve permaganate time.

Alias: 

Chloros, Bleach, Twin Oxide Compound A, Ipo chlor 16%, Ipochlor Bluetech, Sodium Hypo Chlorite 25 Ltr

Active Matter: 
12-15
Application: 

  • Also used as a disinfectant and germicide , especially in the sterilization of water.

  • It is also used for making wool unshrinkable and in the manufactire of chloroform.

  • For the purpose of disinfection and bleaching  , a weak soln. ( 1.2 % ) is used. For purifying water 0.02 to 0 .2 % volumetric is sufficientPotable Water Treatment

  • Aquatics and Pools

  • Odor Control/Corrosion Control

  • Food & Beverage Processing

  • Wastewater Treatment

  • Cooling Towers, Inland Power Stations & Industry

  • Irrigation Systems

  • Agriculture/Farming
     

HANDLING AND STORAGE PRECAUTIONS:

Do not store adjacent to chemicals that may react if spillage occurs. Comply with Oman regulations, when shipped. If closed containers become heated, vent to release decomposition products (mainly oxygen under normal decomposition). Do not mix or contaminate with ammonia, hydrocarbons, acids, alcohol or ethers.

DO NOT REUSE CONTAINERS: Product residues may remain in containers. All labeled precautions MUST be observed. Dispose of container in a manner meeting government regulations.

PRODUCT DISPOSAL:  Product should be completely removed from containers. Material that cannot be used or chemically reprocessed should be disposed of, in a manner meeting government regulations.

Packing Size: 
25.00 Ltr.
Using Procedure: 

6% Sodium Hypochlorite Solution. Disinfectant for use in drinking water. Use one drop of solution per 10 ltrs of drinking water, 600 ml of solution per 36 tons of drinking water.
 

General formulation to calculate  how much bleach is needed to add to a tank or a pipeline to disinfect it to a given chlorine residual using a given disinfectant. Usually someone wants to know how to meet an AWWA Standard (like C651-92, Disinfection of Water Mains). The equation below should be used to estimate the amount of sodium / Calcium hypochlorite (Chlorine Water is 6.00% sodium hypochlorite) needed to disinfect a given quantity of water to a desired chlorine concentration. 

                                                                        req'd residual in ppm
  Volume of hypo  =  volume of water  x  (  ----------------------------- )
                                                                           1,000,000 x hypo %

For example , say you had installed a new 5,000 gallon tank and wanted to make sure that you had at least a 100 ppm solution of chlorine in it.

How much 6.00% Hypochlorite would you need to add  ?

  • (5,000 gal x 100 ppm) / (1,000,000 x .06) = 8.33 gallons

How much 12% Hypochlorite solution would you need ?

  • (5,000 gal x 100 ppm) / (1,000,000 x .12) = 4.17 gallons

If you use calcium hypochlorite (the white, powder version of chlorine, like HTH pool cleaner), the equation becomes:

                                                                                                              req'd residual in PPM
Wgt. of Calcium Hypo (lbs)= gal of water x 8.33 lb / gal m x   ( ----------------------------- )
                                                                                                               1,000,000 x hypo %
  • This is simply the previous equation multiplied by the conversion factor of 8.33 pounds per gallon of water.

Let's assume that we still need to disinfect 5,000 gallons at 100 ppm.

How many pounds of 65% calcium hypochlorite (HTH pool cleaner) are needed?

  • (8.33 lbs/ gal. x 5,000 gal x 100 ppm) / (1,000,000 x .65) = 6.4 pounds
Note: 

Spraying - Following rough washing to a good Water White or better, apply dilute Bleach to 1 - 3% strength.  First wet the tank surface (spray with DI water), then spray all over with Bleach, wait 30 minute (but do not allow to dry) and then rinse very well with DI water, including the tank top towards the sump.  To ensure that you have covered all areas properly, this process should be carried out at least twice with good DI water.

Injection -no.

Re-circulation - Following rough washing  to a good Water White standard or better, apply dilute Bleach to 1-3% strength.  Mix sufficient Bleach with fresh water in the tank and heat this mixture to 40 - 500C, circulate through the drop line if fitted and than circulate through butterworth machine for 3 hours.  After re-circulation immediately warm butterworth to (500 C) the tank for 3 hours at maximum pressure, increase the water temperature to 80-850 C after 45 minutes.  Check (by smell) that there is no Bleach remaining, then fresh water rinse and dry.

** When there are a number of tanks requiring re-circulation, it may be significantly more efficient to make up a large batch or number of batches that can be transferred on between  tanks as required.

* Use a strainer at the pump stack when circulating any solution.
Tank Lining - Stainless / Zinc / Epoxy / Phenolic (Extreme care must be taken if product other than bleach substitute is to be used in any coated space).

**These products become more aggressive with temperature increase, and should not be allowed to dry on tank walls or stored in cargo tanks as cleaning solution or slops.             

Related Products: 
Chlorine Tablets Calcium Based
Chlorine Tabs POWERFUL (3 Inch Jumbo Size)
Chlorine Liquid
Chlorine Scavenger
Sodium Thiosulfate Pentahydrate
Sodium Bisulphite Solution
Sodium Meta Silicate
Bleaching Liquid
WHITEX Bleach Liq
TPOL 20 Ltr BUCKET
Hand Cleaner Paste, Waterless 1 Kg Pkg
Dish Wash 500 ml
Toilet Cleaner-500 ml
Safety Accessories: 
Hand Gloves Chemical resistance
RESPIRATORY PROTECTION HALF MASKS
Goggle
PVC Chemical Resistance Boot
Short Description: 
Extra pure LAB TESTED Clear greenish-yellow liquid miscible in any proportion with water.

Sodium Hypochlorite manufacturer and supplier in Barka, Muscat, Sohar, Oman, Fujairah, Dubai, Sharjah, Abudhabi, Ajman, UAE Middle East, Sudan, Yemen, Nairobi Kenya Africa, Mumbai, Kolkata, Chennai, Visakhapatnam, Gandhidham, Kandla Mundra, Surat Hazira, Gujrat, Navi Mumbai MIDC

Note : Store in cool place

UN No :  1791
IMDG CLASS : 8

PACKING GROUP : III

ODOUR  : IRRITATING, PUNGENT ODOUR

R31: Contact with acids liberates toxic gases

R34: Causes burns

S-PHRASES

S1/2: Keep locked up and out of the reach of children.

S28: After contact with skin, wash immediately with plenty of water

S45: In case of accident or if you feel unwell, seek  medical advice (show the label where possible)

S50: Do not mix with acids

S50: Do not mix with reducing agents

X2: Restricted to professional users.Warning! Avoid exposure - obtain special instructions before use.

EMERGENCY AND FIRST AID PROCEDURES

EYE:

OBJECT IS TO FLUSH MATERIAL OUR IMMEDIATELY AND THEN SEEK MEDICAL ATTENTION IMMEDIATELY flush eyes with a directed stream of water at least 15 minutes while forcibly holding eye lids apart to ensure complete irrigation of all eye and lid tissue. Washing eyes within one (1) minute is essential to achieve maximum effectiveness. SEEK MEDICAL ATTENTION IMMEDIATELY.

SKIN:

SEEK MEDICAL ATTENTION IMMEDIAELY. Flush thoroughly with cold water under shower while removing contaminated clothing and shoes. CONTINUE TO FLUSH UNTIL MEDICAL ATTENTION ARRIVES. Discard non-rubber shoes. Wash clothing before reuse.

INIIALATION:

Remove to fresh air. If breathing is difficult, have trained person administer oxygen. If respiration stops, give mouth-to-mouth resuscitation. GET MEDICAL ATTENTION IMMEDIATELY.

INGESTION:

           NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. If swallowed, DO NOT INDUCE VOMITING. Give large quantities of milk or gelatin solution. If these are not available give large quantities of water. If vomiting occurs spontaneously, keep airway clear and give more milk, gelatin solution or water, GET MEDICAL ATTENTION IMMEDIATELY. Avoid vomiting, lavages or acidic antidotes. NOTE TO PHYSICIAN: Sodium Hypochlorite is an alkaline corrosive. For exposure by ingestion do not use emesis, lavages or acidic antidotes. Dilute immediately by giving milk, melted ice cream, beaten egg white, starch paste or antacids such as milk magnesia. Aluminum hydroxide gel or magnesium trisilicate gel. Avoid sodium bicarbonate because of  carbon di-oxide release. Sodium thiosulphate solution may prove beneficial by reducing unreacted material

 

Other Related PRODUCTS LINKS :

Textile Hypo Bleach , SODIUM HYPO CHLORITE , Sod Hypo Chlorite conc activeCHLORINE , CHLORINE LIQUID , Calcium Hypo Chlorite Conc active Chlorine , Chlorine Tablet cyanurate , Chlorine Tablets Calcium Based , DYE REMOVER ORG DICHLOR , Dechlorination Soln De-Hypo

Chlorine Alkaline Water

  • 9856 reads

Clean GEL

Clean GEL / Paste is highly concentrate paste which is used to clean metal areas and is applied with brush. Useful for preparing metal surface for painting. Paint will adhere better to iron and steel surfaces when cleaned with Clean Jelly.
 

Alias: 

GEL Degreaser

Application: 

It is used to remove heavy scales, discolouration, annealing colours, rust particles near weld and welding affected area by heat without grinding or wire brushing or buffing.

PROBLEM CLEARING AGENT COMMENTS
Rust and other corrosion products. Embedded or adhering "free iron Very light rust stain can be removed by 10% nitric acid. More significant rust or embedded iron will require pickling. Also see previous sections on Passivating and Pickling. Sand or glass-bead blasting is another option Wear PPE as appropriate. Afterwards rinse well with clean water. Mix in acid-proof container, and be very careful with the acid, (See Precautions for acid cleaners)
Routine cleaning of boat fittings. Frequent washing down with fresh water. Recommended after each time the boat is used in salt water.
Cooking pot boiled dry. Remove burnt food by soaking in hot water with detergent, baking soda or amonia. Afterwards clean and polish. with a mild abrasive if necessary. See comments re steel wool.
Dark oxide from welding or heat treatment. "Pickling Paste" or pickling solutions given on previous page. Must be careful rinsed, and use care in handling (see Precautions for acid cleaners).
Scratches on polished (satin or brushed) finish. Slight scratches - use impregnated nylon pads. Polish with polishing wheel dressed with iron-free abrasive for deeper scratches. Follow polish lines. Then clean with soap or detergent as for routine cleaning Do not use ordinary steel wool - iron particles can become embedded in stainless steel and cause further surface problems. Stainless steel and "Scotchbrite" scouring pads are satisfactory.

 

Packing Size: 
5.00 KgPaste
Using Procedure: 

1.Clean Gel / Paste is applied on metal surrounding areas with a nylon bristled plastic brush. Application Temp. = between 5 – 40 deg. C
2. Keep  Paste for 5 to 30 minutes (contact time) depending on contamination, temperature .
3. Use pressurised water jet spray OR wipe the weld seam lightly with plastic brush & wash with water thoroughly.

For Satin / Dull Finish

1. First remove oil, dirt,buffing compounds etc, with Rxsol  Degreaser. Add 50-75 gm/lit. in water (i.e. 1 kg Rxsol Degreaser in 15 to 20 lit. water) & stir to dissolve. Wipe S.S surface with cotton cloth or pressurized spray for 2-5 min. or soak for 10 min. Then, wash with water properly.

2. Clean Gel Paste is applied on weld seam & surrounding areas with a nylon bristled plastic brush or  by Paste sprayer or circulated in pipeline with pump.

Application Temp. = Room temp.( i.e. between 25-35 C). If temperature is less than 25 C, then more time may be required and if temperature is more than 35 C, then uneven preocessing & drying of applied materials may result.Then, cool SS equipment by keeping it in shade or cover by temporary shade to protect that not directly under the sun light.

3. Keep Clean Gel Paste for 10-45 minutes depending on contamination & scale. ( generally kept for 10-30 min. and Pickling Spray generally kept 30-45 min. Depending on SS type and initial condition of SS parts)

4. Wipe the weld seam lightly with plastic brush or cloth & wash the  Paste applied area with water thoroughly.

 

 

For Cleaning Mirror Bright SS Areas

THE BELOW STEPS WILL NOT AFFECT SHINE OF MIRROR BRIGHT POLISHED SS AREAS AND PROVIDE CONTAMINATION & STERILE PARTICLE FREE PASSIVATED SS SURFACE.

1) First apply Clean Gel Paste in weld seam & surrounding areas with a nylon bristled plastic brush. After 10 to 30 min. wipe with cloth or plastic brush & wash water thoroughly.

(Application of Clean Gel Paste ensures that black & red spots do not come on & near weld seams area as generally observed some days after bright buffing.)

2) Complete bright buffing / polishing procedure to make surface mirror bright & shiny.

DISCARD STEPS 1 & 2 ABOVE, IF SS SURFACE IS ALREADY BRIGHT BUFFED OR ELECTROPOLISHED.

3) Remove oil, dirt buffing compounds etc. with RXSOL Degreaser which is Metal Free Degreaser. Add 50-75 gm/lit. in water & stir to dissolve.

Wipe S.S. surface with cotton cloth or pressurised spray for 2-5 min. or soak small parts for 10 min. Wash with water prpoerly.

 

NOTE: It is better to rinse SS surface with 10 gm/lit RXSOL DEGREASER solution as the last step and then rinse with water to ensure complete removal of previously applied Passivate Pickling paste or spray from the surface.

Note: 

Advantage & Benifit

  • Easy to apply.
  • Due to paste easy to use on vertical surface.
  • Simply washed with water.
  • Easy to handle.
  • Easly  remove heavy scales, discolouration, annealing colours, rust particles near weld and welding affected area .
Related Products: 
Rust Convertor
Rust Remover
Rust Stain Remover SAFE JELLY
RX JELLY Pickling Paste
Metal Clean Britte
DE-SCALER DE-LIMER
DEGREASER
Hand Cleaner Paste, Waterless 1 Kg Pkg
TPOL 20 Ltr BUCKET
Heavy Toilet Urinal Cleaner
Dish Wash 500 ml
RXSOL RX 9
Boat Cleaner
Safety Accessories: 
RESPIRATORY PROTECTION HALF MASKS
Hand Gloves Chemical resistance
PVC Chemical Resistance Boot
Chemical Protective Suit
Article News: 
Clean Gel – An effective product to get mirror bright areas
Short Description: 
Clean GEL Paste is highly concentrate paste which is used to clean metal areas and is applied with brush.

#CLEANGEL_MumbaiIndiaKolkata
#Cleangel_DubaiUnitedArabEmirates
#CleanGel_MuscatOman

Clean GEL manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai, Sharjah, UAE, Gulf, Middle East, Muscat Oman, Kenya Africa. Get the best quality of Clean GEL at a competitive price from us. We have ready stock of Clean GEL in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.

FAQ: 
Hull Cleaner
  • 9316 reads

Nitric Acid 98 % Tanker Load

Packing Size: 
20000.00 Kg.Liq
Short Description: 
Passivation chemical
  • 22 reads

GAS TURBINE Cleaner GTC 1000

RXSOL GTC 1000 GAS TURBINE CLEANER is a concentrated, neutral, environmentally friendly, biodegradable, waterbased detergent cleaning fluid for cleaning and corrosion inhibition of gas turbine compressors. One operation cleans and protects the engine -and also inhibits corrosion.

Blend of non-ionic surfactants, corrosion inhibitors, organic solvents and demineralised water.

Alias: 

Clean Blade GTC 1000, Compressor Washing Chemicals GAS TURBINE CLEANER

Active Matter: 
98 - 99%
Application: 

Gas Turbine Compressor Cleaning.

Packing Size: 
220.00 Kg.Liq
Using Procedure: 

By spray ring or lance in either starter-driver (off-line) or fired (on-line) wash as directed by the engine manufacturers, in the quantities recommended in the engine manual. It is essential during hot wash that the cleaner should leave as little ash residue as possible to avoid blocking turbine blade cooling holes. RXSOL GTC 1000 GAS TURBINE CLEANER has a maximum ash content of <0.01%, as part of the compliance with OEM specifications for compressor washing fluid.

The unique corrosion inhibitor allows engines to be left ready for an instant restart, even in salty offshore conditions.

Note: 

Appearance
Clear pale straw coloured liquid with a mild pleasant odour.

Solubility
Completely soluble in water. No agitation required.

Compatibility
Not corrosive or detrimental to any of the materials normally used in gas turbine engines or aircraft components. No adverse effect on synthetic turbine oils.

Related Products: 
Gas Turbine Compressor Cleaning Fluid RXSOL 27
Turbine Kleen 81 RXSOL
Safety Accessories: 
Disc Separator Cleaner HD
Filter Cleaner Engine Oil
Short Description: 
RXSOL GTC 1000 is a concentrated, neutral, environmentally friendly, biodegradable, waterbased detergent cleaning fluid for cleaning and corrosion inhibition of gas turbine compressors.

RXSOL GTC 1000 GAS TURBINE CLEANER Fluid exporter and supplier in Mumbai, Dubai, Kandla, Chennai, Muscat, Visakhapatnam, Kolkata, Fujairah, Sharjah, Abu Dhabi, Muscat Barka Ruwi, Oman, Nairobi Kenya Africa, Sudan, Yemen

Liquid Detergent for Gas Turbine Compressor Cleaning for GE Aircraft

  • 1198 reads

Sodium Cyanide Tablet Form

Packing Size: 
50.00 Kg
Short Description: 
Sodium cyanide is a poisonous compound with the formula NaCN. It is a white, water-soluble solid. Cyanide has a high affinity for metals, which leads to the high toxicity of this salt. Its main application, in gold mining
  • 35 reads

GLYCINE Pharma Grade

Glycine is a non-polar, hydrophobic, non-essential αamino acid. It is the simplest and smallest amino acid among all the amino acids and is chemically neutral in nature. It is used as a component of many animal and insect cell culture media. Some major functions of Glycine in cell culture involve synthesis of proteins in the cells. Hence it is also called proteinogenic amino acid. It also contributes towards cellular purine synthesis.

Alias: 

Aminoacetic acid, Aminoethanoic acid, Glycocoll

Application: 

Glycine has buffering capacity and hence acts as an osmoprotectant for cells in culture. It participates in majority of anabolic reaction such as synthesis of heme, creatine and glutathione. Besides these, the glycine cleavage pathway is found to be associated with cell proliferation of several human tumor cell lines. Presence of glycine in conditioned medium enhances the growth of mouse and cattle embryos. Since glycine acts as an inhibitory neurotransmitter in brain and spinal cord, it is a prime target of many neuro psycho pharmacologic agents.

Packing Size: 
25.00 Kg.PWD
Short Description: 
GLYCINE

GLYCINE (Pharma Grade) manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai, Sharjah, UAE, Gulf, Middle East, Muscat Oman, Kenya Africa. Get the best quality of GLYCINE (Pharma Grade) at a competitive price from us. We have ready stock of GLYCINE (Pharma Grade) in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.

  • 297 reads
stock-clearance.png