Detergent & Soap-12

Coil Brite RXSOL Air Conditioning System

RXSOL-16-1697-005 is a concentrated, high-foaming outdoor condenser coil cleaner and brightener. It effectively foams away stubborn,"baked on" lint, smoke film, insects, feathers, grass, leaves and other deposits from air cooledcondenser coils. The expanding foam pushes contamination out of the coil and is easily rinsed away with water. In addition to removing contaminants, the RXSOL COIL CLEANER formula effectively restores efficiency and reduces operating cost by removing hidden oxidation from the coil surfaces.

Alias: 

Aqua Coil, Air Cooler Coil Cleaner, Acti-Brite

Active Matter: 
63-65
Application: 

RXSOL-16-1697-005 is a special formulation of solvents and acids specifically blended for use in cleaning and brightening outdoor aluminum finned air cooled condenser coils.

Produced and packaged in  our ISO 9001 registered facility.

Packing Size: 
210.00 Ltr.
Using Procedure: 

USES:

Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.

DILUTION RATIOS:

Because RXSOL-16-1697-005 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general guideline:

  • Up to 8-10 parts water to 1 par tRXSOL COIL CLEANER for light cleaning and brightening, when expanding foam is not required.
  • 3-5 parts water to 1 part RXSOL COIL CLEANER for foaming action on difficult cleaning tasks.
  • 1-2 parts water to 1 part RXSOL COIL CLEANER for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.

Note: Do not use RXSOL-16-1697-005 at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-16-1697-005 ). Rinse the treated surfaces as well as the surrounding area thoroughly after use.

Note: 

CAUTIONARY NOTES:

This product is for professional use only.At full strength:
• It will cause burns to skin and eyes.
• Ingestion will cause severe and potentially fatal gastric distress.
• Vapors are harmful and may cause respiratory tract irritation.
• May be harmful to plants.
Refer to MSD sheet for further information. MSD sheets are available at your local wholesaler

.PACKAGE SIZES AVAILABLE:

RXSOL-16-1697-005 is available in 1, 5 and 55 gallon containers

ALTERNATE PRODUCTS:

  • Concentrated Alkaline Coil Cleaner.
     
  • Multi-Purpose Alkaline Cleaner.
     
  • Concentrated Evaporator Coil Cleaner
Short Description: 
This is specially formulated for use as a coil cleaner and filter adhesive for cooling coils of the air- conditioning systems.

#CoilBriteinUAE

#CoilBriteinOMAN

#CoilBriteAirCoolerCoilCleanersupplierInUAE

Coil Cleaner Air Conditioning System manufacturer and supplier in India - Middle East UAE GULF - Oman, Kenya Nairobi, Canada. RXSOL Coil Cleaner Air Conditioning System popular supplier in Mumbai, Kandla, Surat, Kolkata, CHennai, Vizag Visakhapatnam, Haldia, Fujairah Muscat, Abudhabi, Ajman, Dubai, Sharjah, Ghala, Barka Sohar Oman, Jinja Kampala, Uganada, CANADA

Air Cooler Coil Cleaner

2 Ethyl Hexanol

Packing Size: 
50.00 Kg.Liq
Short Description: 
2-Ethyl Hexanol A clear, high-boiling point and low volatiity solvent with a characteristic color.

Sodium Hydroxide Food Grade

Alias: 

Caustic Soda Food Grade

Packing Size: 
35.00 Kg.Liq
Short Description: 
Sodium Hydroxide Food Grade

Sodium Hydroxide Food Grade manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Sodium Hydroxide Food Grade at a competitive price from us. We have ready stock of Sodium Hydroxide Food Grade in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.

Degreaser Heavy Duty

Excellent for removal of oil and grease.  Readily soluble in water in all proportions. It is a unique formulation blended from inorganic, organic compounds and detergents with powerful dispersing agents and aliphatic petroleum distillates.   It is non-corrosive to metal like copper, aluminium, mild steel and plastic. It is non-toxic which makes handling easy.

Ideal for use where chlorinated solvents are undesirable or prohibited.

Alias: 

REM-25, Heavy Oil Remover / Drew Clean 2000, Care clean Degreaser GP. Mariclean, Dumbuster Liquid, HDE 777, CLEANER 1155, SEA SHIELD DEGREASER 79115, OSGR, Arrow C180HDD Heavy Duty Emulsifiable Solvent Degreaser, BYCOTEST- C5 CLEANING AGEN, SUPERVIX, Degreaser Heavy Duty 25 Ltr

Active Matter: 
93-98%
Application: 

Complete removal of dirt, oil, carbonised grease, heavy oil , gum, vegetable oil, lube oil, soot, asphalt, carbon stains etc. Gives clear finish to the surface. Excellent for use as a wash for fuel tankers & as a liquid steam jenny compound.
Specialized & Treated for the really tough daily cleaning problems faced in the proper Maintenance of Industrial and Institutional physical plants.  Can be used as a stripper for all types of waxes and finishes and as a Degreaser where regular cleaners will not perform. May be brushed on, sprayed or used in a dip tank . Excellent for use as a wash for fuel tankers & as a liquid steam jenny compound.

Packing Size: 
25.00 Ltr.
Using Procedure: 

Depending upon contamination 2-25% with fresh water.

It is an extremely versatile heavy duty cleaner suitable for use in soak tanks, high pressure washers, Automated Scrubbing machines and for manual use.

Note: 

RXSOL-10-1005-025  is easily soluble in water Action is quite fast even at low temperature which gives advantages of cleaning under operation And avoid shut down and down time.
Non corrosive to most of the metals / plastics.
Gives clear finish to the surface .
Lower cost due to high concentration

Use undiluted for heavily soiled component
 

Short Description: 
Powerful Emulsifiable Solvent Degreaser with dispersing agents. Readily soluble in water in all proportions. It is non-corrosive to metal like copper, aluminium, mild steel and plastic. It is non-toxic which makes handling easy.

Powerful Emulsifiable Solvent Degreaser with dispersing agents. Readily soluble in water in all proportions. It is non-corrosive to metal like copper, aluminium, mild steel and plastic. It is non-toxic which makes handling easy.

#HeavyDutyDegreaser
#DegreaserMuscatOman
#DegreaserHeavyDutyDubaiUAE
#DegreaserMumbaiKolkataChennaiVizagGandhidham

REM-25, Heavy Oil Remover / Drew Clean 2000, Care clean Degreaser GP. Mariclean, Dumbuster Liquid, HDE 777, CLEANER 1155, SEA SHIELD DEGREASER 79115, OSGR, Arrow C180HDD Heavy Duty Emulsifiable Solvent Degreaser, BYCOTEST- C5 CLEANING AGEN, SUPERVIX, Degreaser Heavy Duty 25 Ltr

We are supplier and stockist of degreaser at all major Indian ports and Middle East ports. We are popular among Ship Suppliers and Chandlers and shipping agent as a marine chemicals supplier which includes Refrigerant Freon 22, Laundry Soap and Detergents, Cleaner and Polish Goods, Hold cleaning and tank cleaning detergent, Oil spill dispersant, carbon remover, Electrocleaner, Water less hand cleaner, Teepol, Coolant, Glycol, Boiler and cooling water treatment chemicals etc...

Degreaser Heavy Duty manufacturer and supplier in Mumbai,Ruwi, Ghala, Barka, Muscat, Oman, Salalah, Fujairah, Dubai, Sharjah, Abudhabi, Ajman, Kolkata, Haldia, Paradip, Visakhapatnam, Chennai, Ennore, Navi Mumbai MIDC

34029019

We supply all marine chemicals products & Lubricants .We arrange to supply Shell /Castrol /Servo / Mobil oils, EP2 Grease, Molykote, Molyslip, Aerosol, Silicone, Petrol, Paraffin oil, coal tar, fish oil, tallow, turpentine, white spirit, Teflon coating, Rustolvo, silicon grease, aerosol spray, molyslip, copaslip, greases, degreaser etc...
 

MARINE CHEMICALS MANUFACTURER SUPPLIER INDIA DUBAI UAE MUSCAT OMAN

MARINE CHEMICALS supplier in United Arab EMIRATES, OMAN, INDIA
Antifreeze Descaling Liquid Oil Spill Dispersant
Air Cooler Cleaner Disc Clean  One Shot Bwt
Alkalinity Control Distilled Water Oxygen Scavenger
Autotreat Ecoclean Oxytreat
Bilge Cleaner Ecosperse Ph Minus
Boiler Coagulant Electric Motor Cleaner Ph Plus
Carbon Cleaner Electrocleaner Rig Wash
Cement & Concrete Cleaner Electrosol Quick Rocor NB
Chlor 12 Enviro 2000 Rust Convertor
Condensate Cleaner Enviroclean Rust & Scale Remover
Coolant/ Antifreeze Fuel Oil Treatment Seaclean
Deck Cleaner Hand Cleaner Soot Remover
Degreaser Hand Gel  Tank Cleaner
Descalex Liquid  Metal Brightener Universal Wash
Descalex Powder NCLT Vap Treat

Oil Grease cleaner Emulsifiable Solvent Degreaser

Cethyl Trimethyl Ammonium Chloride 30 Percent (CATC 30)

Packing Size: 
200.00 Kg
Short Description: 
CTAC 30 (CETYL Trimethyl Ammonium Chloride 30%) Long-chain quaternary ammonium surfactants.

Sodium Lauryl Ether Sulfate 70 %

Packing Size: 
25.00 Kg.Liq
Short Description: 
Excellent Foaming power and detergency properties. It can be used with other anionic, non-ionic or amphoteric surfactants

ANTISCALANT 9209 RX Seawater Distillation Plants

Antiscalant 9209 RX is specially designed to control the development of scale in seawater distillation plants. It is based on a synergistic blend of phosphonates which are found to be more effective than other polymers at controlling carbonate and sulphate scale formation in sea water distillation units .

Alias: 

Hydrex 9209, Metito M 915, Genesys LF

Active Matter: 
94-98
Application: 

PREVENTS IRON FOULING and SILICA ANTISCALANT properties.

  1. Convenient liquid formulation for automatic dosing using suitable dosing equipment.
  2. Prevents formation of hard scale in seawater distillation units.
  3. Performance surpasses other similar products.
  4. Cost effective concentrate.
  5. Effective at high temperatures.
Packing Size: 
30.00 Kg.Liq
Using Procedure: 

The correct dosage rate is dependant upon several parameters, including feed temperature, pH, and chemical analysis and will be specified by your consultant after a detailed survey of your plant. To obtain the best results, Antiscalant 9209 RX should be added continuously using a suitable metering pump.

In general PRACTICE :
Antiscalant 9209 RX should be dosed continuously to the feed water upstream of the cartridge filters. Typical dosage rates are 2 – 4 mg/L.
Antiscalant 9209 RX may also be used in sea water applications where iron is present, recycle of brine is in use or there is no feed water pH reduction by acid dosing.

Typical dose rates are 0.5 – 1.0 mg/L
Antiscalant 9209 RX dose rate in the feed water should be less than 5 mg/L in potable water systems. 
Antiscalant 9209 RX can be diluted and is fully miscible with water in all proportions.
 

Note: 

Antiscalant 9209 RX  is an aqueous solution of neutralised phosphonic acid. It has been approved for use in potable water applications and does not contribute to assimilable organic carbon (AOC), which can act as source of nutrient for micro-organisms. 

Short Description: 
Antiscalant for Water Distillation Units , specially designed to control the development of scale in seawater distillation plants.

ANTISCALANT 9209 RX seawater distillation plants, Compatible with all types of polyamide membrane
ANTISCALANT 9209 RX powerfully Inhibits common scales Calcium carbonate/sulphate - Calcium phosphate, Barium/Strontium sulphate - Silica, Iron/Manganese

#AntiScalant_ManufacturerSupplier
#Antiscalant_DubaiAbudhabiAjmanFujairah
#Antiscalant_MuscatSoharOman
#Antiscalant_MumbaiChennaiKolkataSuratGandhidhamVizag

RXSOL-51-6005-025 ANTISCALANT and Antifoulant for Reverse Osmosis and Nano Filtration unit.

ANTISCALANT 9209 RX FOR seawater distillation plants manufacturer and supplier in Fujairah, Muscat, Barka, Oman, Dubai, Sharjah, Abudhabi, UAE Middle East, Ajman, Mumbai, Kolkata, Kandla, Visakhapatnam, Chennai Surat, CANADA, Kenya Nairobi, Jinja Uganda

ANTISCALANT 9209 RX Seawater Distillation Plants RXSOL-51-6005-025 is Suitable for Reverse Osmosis (RO) and NanoFiltration (NF) membranes

✓ Effective at LSI up to +2.6

✓ Excellent inhibitor for iron fouling

✓ Excellent silica antiscalant

✓ NSF listed product

✓ Approved for use in drinking water applications (UKDWI)

✓ Compatible with all types of polyamide membrane

✓ Replaces acid addition

✓ Inhibits common scales

- Calcium carbonate/sulphate

 - Calcium phosphate

 - Barium/Strontium sulphate

 - Silica

- Iron/Manganese

ANTISCALANT 9209 RX Seawater Distillation Plants RXSOL-51-6005-025 Inhibits Scale Formation, Prevents Iron Fouling

Broad Spectrum Antiscalant and Antifoulant Liquid

Calcoum Nitrate

Packing Size: 
0.00 Box
Short Description: 
Calcium nitrate is a water soluble chemical compound that has numerous uses in water treatment fertilizers concrete and cold packs

Cool Water Treat

Alias: 

C.W.T. Inhibitor 9-111, COOL WATER TREAT NCL, Coolwater Treat, Cool water treat, Cool Treat, Corrosion Inhibitor for Cooling Water, CoolTreat 25 Ltr

Active Matter: 
45-50
Application: 

Cool Water Treat  is a highly effective corrosion inhibitor for all common metals in cooling water systems. Testing has shown no detrimental effects on non metallic substances such as seals, glands, packing, hoses, gaskets etc., normally used in these systems. Where most traditional inhibitors react with the metal surface and form oxides that prevent further corrosion, Cool Water Treat  applies a thin and durable layer of protective molecules to the metal surfaces. This technology prevents the continuous build-up of insulating layers on heat transfer surfaces. For new builds, RXSOL  Ships Service recommends cleaning of the water system before commencing service. The system will always contain small amounts of oil and iron oxides, and this can be removed in one operation. If the system is corroded or is more heavily contaminated, degreasing scale is recommended. For systems previously treated with other products, RXSOL  Ships Service recommend to drain and flush the system before refilling with distilled water and Cool Water Treat . The system should be clean and free from scale and corrosion products when starting the treatment. The use of antifreeze is sometimes required if the vessel is to be laid up in cold areas, Cool water treat can be used in conjunction with glycols for frost protection. If used in conjunction with glycols, It is recommended to increase the product concentration to 8%.*

Packing Size: 
25.00 Ltr.
Using Procedure: 

Cool Water Treat should be dosed to a suitable point in the system. If the expansion tank is used, adequate circulation must be assured.

Dosing and Control

Initial dosage for an untreated system is 60 litres of Cool Water Treat Cool water Treat Corrosion Inhibitor / ton of untreated distilled water (6%). This will provide sufficient protection of the system for a period of two to five years under normal conditions. 6% Cool water Treat Corrosion Inhibitor should also be dosed in all make up water added to the system to compensate for lost coolant. The engine manufacturer's recommendations for water quality should always be complied with. Chloride levels should always be as low as possible. Most engine manufacturers recommend a maximum of 50 ppm chlorides. For this reason, RXSOL Service recommends the use of distilled water as make-up.

Note: 
  • Liquid product, easy to use
  • Environmentally friendly, fully organic product, low toxicity
  • Effective against cavitation and erosion. Superior heat transfer properties
  • Compatible with hoses, gaskets and seals
  • Compatible with glycols for frost protection
  • Stable product-non depleting
  • The product can be used for corrosion inhibition in many types of closed re-circulation system cooling water systems
  • Approved by major engine manufacturers
Short Description: 
Cool water Treat Corrosion Inhibitor can be used in conjunction with glycols for frost protection. If used in conjunction with glycols, It is recommended to increase the product concentration to 8%.*

Cool Water Treat is specialized corrosion inhibitor for Cooling Water system.

#CorroSionInhibitor_CoolingSystem
#CoolingWaterTreatmentChemicals
#CWTinhbitor_ManufacturerSupplierIndiaUAEoman

Cool Water Treat corrosion inhibitor for cooling water system manufacturer and supplier in Mumbai, Navi Mumbai, Gandhidham, Hazira Surat, Chennai Ennore, Vizag Visakhapatnam, Kolkata Haldia, Buzbuz, Paradip, Fujairah, Dubai, Ajman, Abudhabi, Muscat, Oman, Canada, Nairobi Kenya, Sudan, Yemen

Cooling Water Corrosion Inhibitor

Sodium Hypo Chlorite

Sodium Hypochlorite solution, Used for sterlizing water and swimming pool...This will - Remove odors. Remove Color. Improve permaganate time.

Alias: 

Chloros, Bleach, Twin Oxide Compound A, Ipo chlor 16%, Ipochlor Bluetech, Sodium Hypo Chlorite 25 Ltr

Active Matter: 
12-15
Application: 
  • Also used as a disinfectant and germicide , especially in the sterilization of water.

  • It is also used for making wool unshrinkable and in the manufactire of chloroform.

  • For the purpose of disinfection and bleaching  , a weak soln. ( 1.2 % ) is used. For purifying water 0.02 to 0 .2 % volumetric is sufficientPotable Water Treatment

  • Aquatics and Pools

  • Odor Control/Corrosion Control

  • Food & Beverage Processing

  • Wastewater Treatment

  • Cooling Towers, Inland Power Stations & Industry

  • Irrigation Systems

  • Agriculture/Farming
     

HANDLING AND STORAGE PRECAUTIONS:

Do not store adjacent to chemicals that may react if spillage occurs. Comply with Oman regulations, when shipped. If closed containers become heated, vent to release decomposition products (mainly oxygen under normal decomposition). Do not mix or contaminate with ammonia, hydrocarbons, acids, alcohol or ethers.

DO NOT REUSE CONTAINERS: Product residues may remain in containers. All labeled precautions MUST be observed. Dispose of container in a manner meeting government regulations.

PRODUCT DISPOSAL:  Product should be completely removed from containers. Material that cannot be used or chemically reprocessed should be disposed of, in a manner meeting government regulations.

Packing Size: 
25.00 Ltr.
Using Procedure: 

6% Sodium Hypochlorite Solution. Disinfectant for use in drinking water. Use one drop of solution per 10 ltrs of drinking water, 600 ml of solution per 36 tons of drinking water.
 

General formulation to calculate  how much bleach is needed to add to a tank or a pipeline to disinfect it to a given chlorine residual using a given disinfectant. Usually someone wants to know how to meet an AWWA Standard (like C651-92, Disinfection of Water Mains). The equation below should be used to estimate the amount of sodium / Calcium hypochlorite (Chlorine Water is 6.00% sodium hypochlorite) needed to disinfect a given quantity of water to a desired chlorine concentration. 

                                                                        req'd residual in ppm
  Volume of hypo  =  volume of water  x  (  ----------------------------- )
                                                                           1,000,000 x hypo %

For example , say you had installed a new 5,000 gallon tank and wanted to make sure that you had at least a 100 ppm solution of chlorine in it.

How much 6.00% Hypochlorite would you need to add  ?

  • (5,000 gal x 100 ppm) / (1,000,000 x .06) = 8.33 gallons

How much 12% Hypochlorite solution would you need ?

  • (5,000 gal x 100 ppm) / (1,000,000 x .12) = 4.17 gallons

If you use calcium hypochlorite (the white, powder version of chlorine, like HTH pool cleaner), the equation becomes:

                                                                                                              req'd residual in PPM
Wgt. of Calcium Hypo (lbs)= gal of water x 8.33 lb / gal m x   ( ----------------------------- )
                                                                                                               1,000,000 x hypo %

  • This is simply the previous equation multiplied by the conversion factor of 8.33 pounds per gallon of water.

Let's assume that we still need to disinfect 5,000 gallons at 100 ppm.

How many pounds of 65% calcium hypochlorite (HTH pool cleaner) are needed?

  • (8.33 lbs/ gal. x 5,000 gal x 100 ppm) / (1,000,000 x .65) = 6.4 pounds
Note: 

Spraying - Following rough washing to a good Water White or better, apply dilute Bleach to 1 - 3% strength.  First wet the tank surface (spray with DI water), then spray all over with Bleach, wait 30 minute (but do not allow to dry) and then rinse very well with DI water, including the tank top towards the sump.  To ensure that you have covered all areas properly, this process should be carried out at least twice with good DI water.

Injection -no.

Re-circulation - Following rough washing  to a good Water White standard or better, apply dilute Bleach to 1-3% strength.  Mix sufficient Bleach with fresh water in the tank and heat this mixture to 40 - 500C, circulate through the drop line if fitted and than circulate through butterworth machine for 3 hours.  After re-circulation immediately warm butterworth to (500 C) the tank for 3 hours at maximum pressure, increase the water temperature to 80-850 C after 45 minutes.  Check (by smell) that there is no Bleach remaining, then fresh water rinse and dry.

** When there are a number of tanks requiring re-circulation, it may be significantly more efficient to make up a large batch or number of batches that can be transferred on between  tanks as required.

* Use a strainer at the pump stack when circulating any solution.
Tank Lining - Stainless / Zinc / Epoxy / Phenolic (Extreme care must be taken if product other than bleach substitute is to be used in any coated space).

**These products become more aggressive with temperature increase, and should not be allowed to dry on tank walls or stored in cargo tanks as cleaning solution or slops.             

Short Description: 
Extra pure LAB TESTED Clear greenish-yellow liquid miscible in any proportion with water.

Sodium Hypochlorite manufacturer and supplier in Barka, Muscat, Sohar, Oman, Fujairah, Dubai, Sharjah, Abudhabi, Ajman, UAE Middle East, Sudan, Yemen, Nairobi Kenya Africa, Mumbai, Kolkata, Chennai, Visakhapatnam, Gandhidham, Kandla Mundra, Surat Hazira, Gujrat, Navi Mumbai MIDC

Note : Store in cool place

UN No :  1791
IMDG CLASS : 8

PACKING GROUP : III

ODOUR  : IRRITATING, PUNGENT ODOUR

R31: Contact with acids liberates toxic gases

R34: Causes burns

S-PHRASES

S1/2: Keep locked up and out of the reach of children.

S28: After contact with skin, wash immediately with plenty of water

S45: In case of accident or if you feel unwell, seek  medical advice (show the label where possible)

S50: Do not mix with acids

S50: Do not mix with reducing agents

X2: Restricted to professional users.Warning! Avoid exposure - obtain special instructions before use.

EMERGENCY AND FIRST AID PROCEDURES

EYE:

OBJECT IS TO FLUSH MATERIAL OUR IMMEDIATELY AND THEN SEEK MEDICAL ATTENTION IMMEDIATELY flush eyes with a directed stream of water at least 15 minutes while forcibly holding eye lids apart to ensure complete irrigation of all eye and lid tissue. Washing eyes within one (1) minute is essential to achieve maximum effectiveness. SEEK MEDICAL ATTENTION IMMEDIATELY.

SKIN:

SEEK MEDICAL ATTENTION IMMEDIAELY. Flush thoroughly with cold water under shower while removing contaminated clothing and shoes. CONTINUE TO FLUSH UNTIL MEDICAL ATTENTION ARRIVES. Discard non-rubber shoes. Wash clothing before reuse.

INIIALATION:

Remove to fresh air. If breathing is difficult, have trained person administer oxygen. If respiration stops, give mouth-to-mouth resuscitation. GET MEDICAL ATTENTION IMMEDIATELY.

INGESTION:

           NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. If swallowed, DO NOT INDUCE VOMITING. Give large quantities of milk or gelatin solution. If these are not available give large quantities of water. If vomiting occurs spontaneously, keep airway clear and give more milk, gelatin solution or water, GET MEDICAL ATTENTION IMMEDIATELY. Avoid vomiting, lavages or acidic antidotes. NOTE TO PHYSICIAN: Sodium Hypochlorite is an alkaline corrosive. For exposure by ingestion do not use emesis, lavages or acidic antidotes. Dilute immediately by giving milk, melted ice cream, beaten egg white, starch paste or antacids such as milk magnesia. Aluminum hydroxide gel or magnesium trisilicate gel. Avoid sodium bicarbonate because of  carbon di-oxide release. Sodium thiosulphate solution may prove beneficial by reducing unreacted material

 

Other Related PRODUCTS LINKS :

Textile Hypo Bleach SODIUM HYPO CHLORITE , Sod Hypo Chlorite conc activeCHLORINE , CHLORINE LIQUID , Calcium Hypo Chlorite Conc active Chlorine , Chlorine Tablet cyanurate , Chlorine Tablets Calcium Based , DYE REMOVER ORG DICHLOR , Dechlorination Soln De-Hypo

Chlorine Alkaline Water

stock-clearance.png