Rig Oil Field

Ready to use for tank cleaning or general degreasing.

RXSOL-20-2023 is   applied  by  Spraying , Brushing, Soaking,  Dipping , Rubbing,  or     Mopping Spraying  is  used for cold cleaning  interiors of oil storage  tanks or  where surfaces to  becleaning   interior  or oil  storage tanks or  where surfaces to be cleaned are irregular. After spraying  RXSOL-20-2023 should  be allowed  to remain for 10 to 20 minutes before rinsing. If  dry surfaces  is not  required it is necessary to rinse with water .Brushing and mopping is used with  RXSOL-20-2023  for removing oil from decks  piers and other large areas .
Dipping & soaking in unheated  RXSOL-20-2023 is the most economical way of cleaning small or large parts.Rubbing with a soft cloth or  sponge soaked  with RXSOL-20-2023  is an easy and quick method of  cleaning larger  parts and painted surface. Steam  cleaning can be speeded up by spraying RXSOL-20-2023 a few minutes prior to steam lancing.

Refer technical datasheet.

Do not soak overnight with these materials.
Always try small test area at first to determine the best dilution rate for the cleaning.
Economical - Highly concentrated
can beDiluted up to 5 or 10 parts with water

Directions for Use and Dose Rates "Emulsifier Solvent Degreaser"

RXSOL-20-2027-025 is  specially formulated for cleaning double bottom, deep and wing tanks etc, used for fuel oils. It can also be used for local cleaning and degreasing of engine rooms and on deck.

Soak Method

for heavy soil put parts into undiluted RXSOL-20-2027-025, for general soiling use a solution of 10-30% RXSOL-20-2027-025 in water. Parts should be soaked for at least 30 minutes before washing off with water.

Spraying Method

Use neat RXSOL-20-2027-025 over all soiled areas. Allow 10-20 minutes for reaction , then rinse with high pressure water hose., Scrubbing will assist the cleaning operation  for stubborn deposits.

Rock and Roll Method

Recommended time to clean and gas-free under normal circumstances would be 3-6 days ,for cleaning of double bottom tanks at sea.
1) First of all  heat the remaining oil in tanks .
2)By stripping constantly. flush the tank with sea water, 
3) Close  all suction and discharge valves .
4) 1st  Dose  Fill the tanks by ½ to 1 litre RXSOL-20-2027-025 per tone of     water   through pipe or manhole , for  75-80% of capacity of tank to be cleaned.
5) Then fill tank to 25% capacity with sea water, raise the temperature up to 60°C maximum, and maintain this temperature for 24 hours.
6) Top up tank to 75-80% capacity with sea water, continue to heat for 48 to 72 hours.
7) Discharge and strip tank. Fill to 50-60% capacity with sea water and allow 2 hours rinsing time.
8) Discharge tank and strip, flushing tank with sea water for 2 hours,stripping continuously. When completed, inspect tank to ascertain if second cleaning is required. If so:
9) For completion add second dose of RXSOL-20-2027-025, fill tank with sea water 75-80% capacity and raise the temperature to 60°C maximum. Maintain this for 48 to 72 hours. And recirculate the solution .
10) Discharge and strip tank, flush with sea water, stripping continuously for 2 hours.
11) To gas-free, fill tank with sea water to overflow through vents and sounding pipes, discharge and strip completely.

Its highly concentrated formulation is so strong that only 1 spoonfull cleans an entire sinkfull of dirty utensils. RXSOL dish wash gel doen't leaves white powder residue like dishwash bars.

Dilute 0.3 to 5% of solution with fresh water.

Economical Usage:-

Dilute the concentrate RXSOL-22-3005  with fresh water between 0.3 to 5 % ratio , then spray the solution on surface to be clean  , for heavily soiled areas , a preliminary cleaning is required. Allow solution to penetrate soil for for complete emulsification about 3-5 minutes before washing off thoroughly with high pressure water. 

GENERAL WASH:-

Dilute 1 part concentrate to 5 parts water or up to 20 parts water depends on contamination of deposit 
RXSOL-22-3005can be used for conventional cleaning using brush, rag or spray . Allow solution 3-5 minutes for emulsification, then rinse off with water .