Electrical

A. Soaking method

Fill a soaking tank filled with a 3:1 solution of RXSOL Solvent Clean in water and stir continuously to allow even distribution of the corrosion inhibitors. Due to its high evaporation rate, a water seal is required to stop the phenomenon, thus allow one (1) hour for the water seal to form. Place the parts to be cleaned into the solution and let them soak until deposits are completely dissolved and can be removed. (soaking time depends on the thickness and composition of the deposits). Remove parts from the bath through water seal (which provides a first rinsing) and rinse with a stream of water. Hard, persisting deposits may be removed with a wire brush.

 B. Brushing method

For large, heavy pieces, RXSOL Solvent Clean  is applied with a brush. Brush the treated area until  the deposits are saturated, loosened and can easily be removed. Spray with water to rinse and then use a cloth to dry.

 C. Closed Circuit

Recirculate undiluted RXSOL Solvent Clean  prior to blowing steam through the system to be  cleaned in order to remove the residual oil. Heat up to 50oC for better results. Circulation time depends on the degree of fouling and may vary from 4 to 24 hours. Upon completion, drain and flush with water or Diesel and Kerosene.

Dilution: Ready to Use, No Dilution Necessary

USES:

Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.

DILUTION RATIOS:

Because RXSOL-16-1697-003 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general
guideline:

• Up to 8-10 parts water to 1 part RXSOL Active Chem  for light cleaning and brightening, when expanding foam is not required.
• 3-5 parts water to 1 part RXSOL Active Chem  for foaming action on difficult cleaning tasks.
• 1-2 parts water to 1 part RXSOL Active Chem  for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.

Note: Do not use RXSOL-16-1697-003 at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-16-1697-003 . Rinse the treated surfaces as well as the surrounding area thoroughly after use.

APPLICATION METHODS:

Low pressure, acid resistant tank sprayers are recommended.
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.

SUGGESTED INSTRUCTIONS FOR USE:

•  When handling RXSOL-16-1697-003 or any other strong chemical, be sure to wear chemical imperviousgloves,apron and splash goggles.
   
• Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.
   
• As with mixing all acids, place the desired amount of water into the tank and then add RXSOL-16-1697-003
   
•   Turn off fans and allow hot coils to cool before applying.
   
• Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.
   
• Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve desired results.
• If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.
   
•   Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process

Preparation / Usage
CARBON REMOVER can be used on boats, in dockyards or in land installations, to clean nozzles, burners, heaters, and injectors for all types of pistons, valves, etc. It is formulated to be used undiluted in immersion or recirculation tanks, brushed or in conjunction with a small pump. After cleaning, rinse thoroughly with water and dry the part completely.