Brick / Concrete sealer
Product Description | Product Application | Product Notes| Product DOSE
Best and Economical products for Concrete & Brick Sealer for protection of damp and water penetration through brick, cement and concrete. It has a unique action that acts as a one way valve allowi
Best and Economical products for Concrete & Brick Sealer for protection of damp and water penetration through brick, cement and concrete. It has a unique action that acts as a one way valve allowing the vapour out but not allowing the water in due to its high water reppellent in nature.
RXSOL All Purpose Concrete, Brick, & Stone Sealer is a penetrating, silane-siloxane water repellent that bonds beneath the surface of concrete and masonry surfaces to protect against the damaging effects of water. This product can be used on any exterior, above-grade, untreated concrete or masonry surface. It is non-film forming, and will not alter surface color or appearance to most surfaces when properly applied.
This product can be used on any exterior, porous concrete or masonry surface including: concrete wall sealer, concrete driveway sealer, concrete sidewalk sealer, concrete patio sealer, brick wall sealer, brick walkway sealer, brick patio sealer, cultured stone wall sealer, manufactured stone wall sealer, stone veneer sealer, and any surface made with sandstone, limestone, natural stone, or porous granite surface.
For best results, use RXSOL All Purpose Concrete & Masonry Cleaner to clean the surface before using this product. Note: this product is not designed for interior use.
Code: RXSOL-67-6702-005
Other Equivalent Brand Water Proof Coat
Short Description: Best and Economical products for Concrete & Brick Sealer for protection of damp and water penetration through brick, cement and concrete.
Brick / Concrete sealer
Application:
The best application for Brick Seal is where faulty guttering or porous brickwork has allowed water to enter the surface. Just apply 2 coats at 24 hour intervals. There should not be a water contac
The best application for Brick Seal is where faulty guttering or porous brickwork has allowed water to enter the surface.
Just apply 2 coats at 24 hour intervals. There should not be a water contact on the surface up to 24 hours after the application.
Common Use: Damp basements, foundation walls, concrete blocks, cinder blocks, slab-on-grade, damp concrete floors, concrete blocks, cinder blocks, sweating garage floor, deteriorated outdoor concrete, dusting concrete, limestone, sandstone foundation.
Using Procedure:
dilute up to 10 - 25 % with fresh water , before application.
Note:
WATER BASE WATER & DIRT REPELLENT FOR BRICKS & CONCRETE RXSOL Brick & Concrete Sealer is an ecological formulation which protects brick and concrete from moisture. The anti stain action is due to
WATER BASE WATER & DIRT REPELLENT FOR BRICKS & CONCRETE
RXSOL Brick & Concrete Sealer is an ecological formulation which protects brick and concrete from moisture. The anti stain action is due to its technologically advance formation, protecting deep inside the brick pores for a long period of time. RXSOL Brick & Concrete Sealer does not change natural aspect of the surface and it will not create any type of film or plastic effect while allowing vapour to escape and is UV resistant.
- WATERPROOFS - Deep seals porous brick, mortar, and masonry waterproofing it against rain and surface water.
- REPELS – Sheds surface water, oil, chemicals, spills on smoother surfaces.
- RESTRICTS - Water vapor transmission.
- REDUCES - efflorescence and concrete dusting.
- CONCRETE & BRICK PRIMER - Allows for use of paints or coatings like epoxy, urethane, acrylics (but not latex).
Technical Specifications:
Product Description
RXSOL-67-6702-005 is a cost-effective solution that permeates an unsealed cementitious surface to boost a substrate's top layer's density, hardness, and strength without sacrificing breathability. For concrete surfaces that have been burnished, polished, or machine troweled, this treatment is perfect. Following a chemical reaction between the sealer and the surface, the RXSOL-67-6702-005 enhances the surface's durability and abrasion resistance, offers long-term protection against wear and traffic, lessens dusting that isn't actually caused by surface defects, and lowers the surface's total care requirements. It can also be used as a helper for polishing concrete since it increases the initial hardness of the surface, which shortens the polishing process and results in a denser and smoother burnished or polished surface. Sealer is non-flammable, compliant with VOCs, and environmentally beneficial.
Sealer has an odorless solution that is suitable for indoor usage, is non-flammable, and complies with VOC regulations. The look of RXSOL-67-6702-005 is obvious. When applied correctly, the substrate will dry with minimal to no change in appearance. Nonetheless, burnished or polished surfaces may typically be given a polished look by applying with a scrubber or polisher and polishing with a white pad after.
Surface Preparation
The optimal substrates for sealing will be at least 28 days old and/or totally cured. When concrete is first put, its surfaces need to be dry, clean, free of bleed water, finished in terms of finishing, and porous enough to allow the concrete to seep into the substrate. Waiting three to seven days after placement, when peak hydration and off-gassing have sufficiently slowed to provide improved sealer penetration into the substrate, can yield further benefits. Surface laitance, dust, dirt, debris, mildew, oil, grease, past sealers, curing agents, paint or other surface coatings, and other pollutants should all be removed from substrates that are already in place. Before applying any cleaning solution or acid to the surface to be cleaned or etched, be sure the surface is fully neutralized.
Application
Prior to application, porosity should always be tested, especially on extremely dense surfaces. For the sealer to penetrate well, the surface needs to be dry. Applying to moist or damp surfaces is not advised. The product only needs to be mixed once; it is a one-part system. Mix the mixture well both in preparation and when applying. Use a temperature of no less than 40°F or more than 95°F for applying or drying. Using a low pressure sprayer, apply evenly. To keep the edge wet while applying material, work in tiny, controllable sections at a time. The product need to be applied to the brink and completely absorbed, free of puddles, in ten minutes.
To ensure that the product is applied evenly and disperses any puddles, use a broom, roller, or microfiber pad. Excessive application of the product may leave behind white residue, particularly on darker or colored surfaces, although this residue usually goes away with time or with power washing. After applying the sealer for the last time, thoroughly rinse the surface with water for two hours, and then sweep up any leftover material to lessen the possibility of white residue remaining on the surface. In most cases, just one application is needed. Wait about one to two hours in between coats if you want to use more product and want to apply more coats.
Apply with a floor scrubber (black pad) or high speed polisher for a more polished look on burnished or polished surfaces. After 12 hours, buff with a white pad. Utilizing warm water, clean the application materials.
Coverage
300-400 sq. ft./gal. for machine troweled and smooth surfaces. 200-250 sq. ft./gal. for broom finished concrete surfaces
Physical Properties
AppearanceLiquid
OdourOdourless
Density>1.1
pH10-12
Limitations
RXSOL-67-6702-005 is designed to work only on porous concrete surfaces and is not intended for asphalt. This product may damage vegetation or may etch glass, vinyl, aluminum, plastic, and metal. Avoid contact with eyes and skin. Sealer may be damaged if frozen prior to use. Not intended to seal cracks. Will not remediate structurally unsound surfaces with defects such as chronic dusting or chalking. The use of high alkaline or acidic cleaners on the treated surface is not recommended and can be damaging. The Company does not warranty specific performance results or compatibility with products manufactured by others. The Company shall bear no liability, other than replacement of defective product. A small test must be conducted prior to application. Based upon this test, the purchaser shall determine for themselves the suitability of this product for the intended use.
Remarks:
Avoid contact from SOLVENT after application.
- Clear, Water Repellent Protection for All Exterior, Porous Masonry & Concrete Surfaces Including Concrete, Brick, Natural Stone, Sandstone, Limestone, Cultured Stone (Stone Veneer/Manufactured Stone), Granite, and More
- Waterproofs and Protects Masonry & Concrete Surfaces from Water Damage & Freeze/Thaw Damage
- Doesn't Form a Film, Allows Trapped Moisture to Escape Which Prevents Pitting, Cracking & Delaminating
- Water-Based/Eco-Friendly - Soap & Water Cleanup, Low Odor
Brick / Concrete sealer manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Brick / Concrete sealer at a competitive price from us. We have ready stock of Brick / Concrete sealer in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
Packing Size: 5.00 Ltr.
Available Packing Size: 5 / 20 / 25 / 35 / 210 Kg
Article News:
,
HASHTAG:
#MarineChemical #TankCleaner #OilFieldChemical #ChemicalManufacturer #ChemicalSupplier #WaterTreatmentChemical #ROchemicals #ReverseOsmosisChemical #Dispersant
#Demulsifier #WaterlessHandCleaner #AirCoolerCleaner #CarbonRemover #ScaleRemover #ActivatedAlumina #ActivatedCarbon #SilicaGel #Degreaser_Biodegradable
#DieselExhaustFluid #BlueLiquid #ToiletBlueWater_Juice #RigWash #OxygenScavenger #CoolingWaterTreatment #RoccorNB #CorrosionInhibitor #CalciumChloride #DIwater
#AlumPowder #MagnesiumSulphate #SodaAsh #SulfamicAcid #PotassiumChloride