Product Application
- 8022198 reads
Depending on contamination 50 - 200 ml per 10 litrs of water . i. e. 200 mol to a bucket of water .
Method of Application and Dose Rates:
1.Direct injection method for tank washing machines. Dose rate 1-5 litres per ton wash water (0.1-0.5%).
2.Recirculation method. Dose rate 1-7 litres per ton wash water (0.1-0.7%).
3.Spot cleaning. Hand spray neat or diluted with up to
4.Five parts water and leave for several minutes before rinsing off with clean water.Cleaning of Cargo Tanks to
remove Soot from Inert Gas Systems.
5.Spray RXSOL-12-1501-AP-210 on with a high pressure cleaning machine and use1:6 with water.If used with hand
sprayer,spray the product neat onto the surface,allowing1 lit.for every12 m2.Use a5-8%solution in a tank
washing machine.
6.Leave for about 30-45 minutes.The surface should be kept wet.
7.Wash down with hot water (80°C) and check the cargo tank
8.Repeat the procedure if necessary.
Note: Whenever possible,the cleaning solution should be heated to 60-80°C.If this method is not possible,other conventional methods such as separate rate direct injection,recirulation or hand spraying provide acceptable options.For boiler fire side cleaning,a 10-20 % hot solution, (temp.above 40°C),should be sprayed on to the surfaces to be cleaned.Allow to penetrate for 20 minutes and flush off. For deposits which are very hard to remove, increase the concentration to 50% and repeat if necessary
Product Properties:
| Appearance | Pale yellow liquid | |
| Density | In g/cm3 at 15°C: 1.01 | |
| Compatibility Metal | No known effect | |
| Rubber | No known effect | |
| pH | Alkaline | |
| PACKAGING | RXSOL-12-1501-AP | Size (in Litres) 25, 35 |
For cleaning engine parts like fuel and lube oil filters , injection nozzles , pump parts , inlet and exhaust valves and cleaning of hard surfaces , such as deck , tanks , engine - rooms , etc
The Importance of RXSOL-12-1501-AP-25 by High-Pressure Cleaning The job of high pressure cleaning can be done easier & quicker by simply using RXSOL-12-1501-AP-25 in correct dosa -ges. Using a high pressure cleaner alone, without any CLEANER, will not achieve optimal cleaning results High-pressure cleaning primarily refers to cleaning of Hard surfaces, such as Decks, Tanks, Engine-rooms, etc. and in the majority of cases the cleaning is done according to the so-called two-step method:
Step 1 : Spraying the RXSOL-12-1501-AP-25 over the area to be cleaned.
Step 2 : Washing down the area using a high-pressure water jet After the RXSOL-12-1501-AP-25 has been sprayed on the surface and before
The wash down begins, the chemicals penetrates & thoroughly moistens dirt & other grime. During wash down, the RXSOL-12-1501-AP-25 thoroughly dissolves the particles of dirt, even oil and fat, in the water spray and thus achieves optimal cleaning results. In addition to being more effective, the use of RXSOL-12-1501-AP-25 substantially reduces the time required for the Cle -aning operation, as well as preventing dirt from reforming on the surface. The use of RXSOL-12-1501-AP-25 in correct dosages is half the job done. 3 Pieces of Good Advice Apply RXSOL-12-1501-AP-25 on dry surface where possible!A dry surface will absorb far better than a wet surface.When applying RXSOL-12-1501-AP-25 on vertical surfaces: Start application from the bottom and work upwards! If beginning from the top and going downwards, the RXSOL-12-1501-AP-25 may produce "channels" down the surface, thereby running too fast off the surface. During high pressure cleaning:It is important that the rinsing water does not run over non-cleaned surfaces! The rinsing water can draw soap from the surface if running over non-cleaned surfaces. High pressure together with optimum concentration of RXSOL-12-1501-AP-25 will give the best effect.
Characteristics:
• Removes grease, oil, carbon deposits, soil and grime.
• Keeps loosened deposits in suspension preventing re-deposition.
• Low toxic.
• Biodegradable.
• Non-flammable.
• Free from hydrocarbon solvents.
• Effective and economical in use
• Water-based cleaner.
• RXSOL-12-1501-AP-210 has numerous cleaning applications including removal of greases, waxes,
oil, sludge, soot, carbon deposits and general dirt and grime.
• Non-corrosive to ferrous metals.
• Suitable for all tank-coatings.
• Can be used for gas and hydrocarbon freeing of tanks.
• Can be used for deodorizing
• Contains wetting agents.
• Leaves surfaces residue free. Page 2 of 3 : 3 :
• Acceptable for use in food areas.
• Suitable for accommodation cleaning of woodwork, leather, desks, etc.
• Suitable for cleaning of toilets and showers.
• Suitable for cleaning of reefer boxes.
• Can be used for cleaning of windows and portholes.
• Can be used for cleaning of dishes.
• Can be used for cleaning of hospitals.
• Can be used for hand laundry cleaning.
